{"product_id":"for-dji-robomaster-s1-intelligent-educational-robot-with-hd-1080p-camera-remote-control-smart-robot-toy","title":"For DJI RoboMaster S1 Intelligent Educational Robot with HD 1080P Camera Remote Control Smart Robot Toy","description":"\u003cp\u003e\u003cb\u003eFor DJI RoboMaster S1 Intelligent Educational Robot with HD 1080P Camera Remote Control Smart Robot Toy\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eSpecifications:\u003c\/b\u003e\u003cbr\u003eCamera\u003cbr\u003eFOV: 120°\u003cbr\u003eMax Still Photo Resolution: 2560×1440\u003cbr\u003eMax Video Resolution: FHD: 1080\/30fps; HD: 720\/30fps\u003cbr\u003eMax Video Bitrate: 16 Mbps\u003cbr\u003ePhoto Format: JPEG\u003cbr\u003eVideo Format: MP4\u003cbr\u003eSensor: CMOS 1\/4”; effective pixels: 5 MP\u003cbr\u003eOperating Temperature Range: -10 to 40°C (14 to 104°F)\u003cbr\u003e\u003cbr\u003eNarrow Infrared Units\u003cbr\u003eEffective Range [1]: 6 m (in indoor lighting conditions)\u003cbr\u003eEffective Area: varies from 10° to 40°, effective area decreases as distance from the target increases\u003cbr\u003e\u003cbr\u003eWide Infrared Units\u003cbr\u003eEffective Range [1]: 3 m (in indoor lighting conditions)\u003cbr\u003eEffective Width: 360° (in indoor lighting conditions)\u003cbr\u003e\u003cbr\u003eHit Detector\u003cbr\u003eDetection Requirements: For the Hit Detector to be activated, the following conditions must be met: Gel bead diameter ≥6mm, launching speed ≥20m\/s, and the angle between the hit direction and hit detector plane is no less than 45°\u003cbr\u003eMaximum Detection Frequency: 15 Hz\u003cbr\u003e\u003cbr\u003eS1\u003cbr\u003eWeight: Approx. 3.3 kg\u003cbr\u003eSize: 320×240×270 mm (length × width × height)\u003cbr\u003eChassis Speed Range: 0-3.5 m\/s (forward) ; 0-2.5 m\/s (backward) ; 0-2.8 m\/s (sideways)\u003cbr\u003eMax Chassis Rotational Speed: 600°\/s\u003cbr\u003eM3508I Brushless Motor\u003cbr\u003eMax Rotational Speed: 1000 rpm\u003cbr\u003eMax Torque: 0.25N m\u003cbr\u003eMax Output Power: 19 W\u003cbr\u003eOperating Temperature Range: -10 to 40°C (14 to 104°F)\u003cbr\u003eDriver: FOC\u003cbr\u003eControl Method: closed-loop speed control\u003cbr\u003eProtection: overvoltage protection; overtemperature protection; soft-start; short-circuit protection; chip and sensor anomaly detection \u003cbr\u003e\u003cbr\u003eGimbal\u003cbr\u003eControllable Range: Pitch: -20° to +35°; Yaw: ±250°\u003cbr\u003eMechanical Range: Pitch: -24° to +41°; Yaw: ±270°\u003cbr\u003eMax Rotational Speed: 540°\/s\u003cbr\u003eVibration Control Precision (on the flat surface and with the Blaster idle): ±0.02°\u003cbr\u003e\u003cbr\u003eBlaster Transmitter\u003cbr\u003eControllable Launching Frequency: 1-8\/s\u003cbr\u003eMax Launching Frequency: 10\/s\u003cbr\u003eInitial Launching Speed: Approx. 26 m\/s\u003cbr\u003eAverage Load: Approx. 430\u003cbr\u003e\u003cbr\u003eIntelligent Controller\u003cbr\u003eLatency (depending on environmental conditions and mobile device): connection via Wi-Fi: 80-100ms; connection via Router: 100-120ms (unobstructed, free of interference)\u003cbr\u003eLive View Quality: 720p\/30fps\u003cbr\u003eMax Live View Bitrate: 6Mbps\u003cbr\u003eTransmission Distance: \u003cbr\u003eConnection via Wi-Fi:\u003cbr\u003eFCC, 2.4GHz 140m, 5.8GHz 90m\u003cbr\u003eCE, 2.4GHz 140m, 5.8GHz 70m\u003cbr\u003eSRRC, 2.4GHz 130m, 5.8GHz 130m\u003cbr\u003eMIC, 2.4GHz 140m\u003cbr\u003eConnection via Router:\u003cbr\u003eFCC, 2.4GHz 180m, 5.8GHz 300m\u003cbr\u003eCE, 2.4GHz 180m, 5.1GHz 100m\u003cbr\u003eSRRC, 2.4GHz 180m, 5.8GHz 300m\u003cbr\u003eMIC, 2.4GHz 170m, 5.1GHz 180m\u003cbr\u003eTransmission Frequency: \u003cbr\u003e2.400-2.4835GHz\u003cbr\u003eFCC:≤30dBm\u003cbr\u003eSRRC:≤20dBm\u003cbr\u003eMIC:≤20dBm\u003cbr\u003e5.170-5.25GHz\u003cbr\u003eFCC:≤30dBm\u003cbr\u003eSRRC:≤23dBm\u003cbr\u003eMIC:≤23dBm\u003cbr\u003e5.725-5850GHz\u003cbr\u003eFCC:≤30dBm\u003cbr\u003eSRRC:≤30dBm\u003cbr\u003eTransmission Standard: IEE802.11a\/b\/g\/n\u003cbr\u003e\u003cbr\u003eIntelligent Battery\u003cbr\u003eCapacity: 2400mAh\u003cbr\u003eStandard Voltage: 10.8V\u003cbr\u003eCharging Limit Voltage: 12.6V\u003cbr\u003eBattery Type: LiPo 3S\u003cbr\u003eEnergy: 25.92Wh\u003cbr\u003eWeight: 169g\u003cbr\u003eWorking Temperature: -10℃~40℃\u003cbr\u003eCharging Ambient Temperature: 5℃~40℃\u003cbr\u003eMaximum Charging Power: 29W\u003cbr\u003eEndurance: 35mins (measured at a constant speed of 2.0m\/s on a flat road)\u003cbr\u003eStandby Battery Life: about 100mins\u003cbr\u003e\u003cbr\u003eCharger\u003cbr\u003eInput: 100-240V, 50-60hZ, 1A\u003cbr\u003eOutput: battery interface: 12.6V=0.8A or 12.6V=2.2A\u003cbr\u003eVoltage: 12.6V\u003cbr\u003eRated Power: 28W\u003cbr\u003e\u003cbr\u003eBlaster\u003cbr\u003eDiameter: 5.9-6.8mm\u003cbr\u003eWeight: 0.12-0.17g\u003cbr\u003e\u003cbr\u003eAPP\u003cbr\u003eApp: RoboMaster\u003cbr\u003eiOS: iOS 9.0 or higher version\u003cbr\u003eAndroid: Android 5.0 or higher version\u003cbr\u003e\u003cbr\u003eRouter\u003cbr\u003eRecommended Router Model: TP-Link TL-WDR8600; TP-Link TL-WDR5640 ( China ); TP-Link Archer C7; NETGEAR X6S ( Oversea )\u003cbr\u003e\u003cbr\u003eMemory Card\u003cbr\u003eSupport Memory Card Type: Micro SD card, maximum support 64GB\u003cbr\u003e\u003cbr\u003e\u003cb\u003ePackage Included:\u003c\/b\u003e\u003cbr\u003e1 x Chassis Front Armor \u003cbr\u003e1 x Mecanum Wheel Mounting Plate \u003cbr\u003e4 x Mecanum Wheel Damping Ring \u003cbr\u003e48 x Mefanum Wheel Roller \u003cbr\u003e1 x Grease \u003cbr\u003e1 x Motion Controller \u003cbr\u003e1 x Bottled Gel Beads \u003cbr\u003e1 x Screwdriver Handle \u003cbr\u003e4 x M3508I Brushless Motor and ESC \u003cbr\u003e4 x Motor Mounting Plate \u003cbr\u003e4 x Screw Box \u003cbr\u003e1 x Safety Goggles \u003cbr\u003e1 x X-Shaped Front Shaft Cover\u003cbr\u003e1x Cable Retainer\u003cbr\u003e1 x Intelligent Battery Charger \u003cbr\u003e1 x Intelligent Battery \u003cbr\u003e1 x AC Power Cable\u003cbr\u003e2 x Left-Threaded Inner Hub \u003cbr\u003e2x Left-Threaded Outer Hub \u003cbr\u003e2 x Right-Threaded Inner Hub \u003cbr\u003e2 x Right-Threaded Outer Hub \u003cbr\u003e4 x Damping Ring Bracket \u003cbr\u003e1 x Chassis Cabin Cover \u003cbr\u003e1 x Masking Tape \u003cbr\u003e7 x Vision Marker \u003cbr\u003e1 x Chassis Cover \u003cbr\u003e1 x Chassis Middle Frame \u003cbr\u003e1 x Intelligent Controller \u003cbr\u003e1 x Front Axle Cover \u003cbr\u003e1 x Front Axle Module Base\u003cbr\u003e1 x Gimbal \u003cbr\u003e1 x Camera \u003cbr\u003e1 x Blaster \u003cbr\u003e1 x Gel Bead Container \u003cbr\u003e1 x Speaker \u003cbr\u003e4 x Hit Detector \u003cbr\u003e1x Camera Cable \u003cbr\u003e1 x Data Cables 35 cm\u003cbr\u003e2x Data Cables 23 cm \u003cbr\u003e4 x Data Cables 12 cm \u003cbr\u003e1 x Chassis Rear Armor \u003cbr\u003e1 x Chassis Left Armor \u003cbr\u003e1 x Chassis Right Armor \u003cbr\u003e\u003cbr\u003e\u003cb\u003e\u003cfont color=\"#FF0000\"\u003eNote:\u003cbr\u003eThe robot is not assembled. Detailed assembly tutorial videos are available in the app and online.\u003c\/font\u003e\u003c\/b\u003e\u003c\/p\u003e\u003cp\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-01.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-02.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-03.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-04.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-05.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-06.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-07.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-08.jpg\"\u003e\u003c\/p\u003e\u003cp\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-09.jpg\"\u003e\u003cimg style=\"width: 1457px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/64962\/64962-10.jpg\"\u003e\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003cb\u003eF.A.Q.\u003c\/b\u003e\u003cbr\u003eBasic Operation\u003cbr\u003eHow can I control the RoboMaster S1?\u003cbr\u003eThe RoboMaster S1 can be operated byusing a computer or a smart device via the touchscreen and gamepad. When using the gamepad with a touchscreen device, the robot can also be operated using an external mouse, which can be connected through a dedicated USB port.\u003cbr\u003e\u003cbr\u003eHow can I connect to the RoboMaster S1?\u003cbr\u003eUsers can connect to the RoboMaster S1 via Wi-Fi or a router. When connecting via Wi-Fi, your mobile device or computer connects to the Wi-Fi of the S1. Connection via router provides broader signal coverage, which allows multiple control methods for robots to operate simultaneously on the same network.\u003cbr\u003e\u003cbr\u003eWhen operating the S1 through a router, does the router need to be connected to the internet?\u003cbr\u003eNo.\u003cbr\u003e\u003cbr\u003eWhat are the product requirements for the router?\u003cbr\u003e1.The encryption mode of the router Wi-Fi needs to be no encryption or wpa\/wpa2-psk\u003cbr\u003e2.Make sure that the number of devices connected to router doesn’t reach the maximum value.\u003cbr\u003e3.The router needs to allow communication among the linked devices.\u003cbr\u003e4.The router connection does not need to do login confirmation twice.\u003cbr\u003e\u003cbr\u003eWhat types of surfaces are okay for the RoboMaster S1 to operate on?\u003cbr\u003eFlat surfaces such as wood, carpet, tile, and concrete are optimal for operating the S1. Users should avoid surfaces that are too smooth as the S1 wheels may have problems gaining enough traction for precise control. Surfaces with fine particles like sand or dirt should be avoided.\u003cbr\u003e\u003cbr\u003eHow long is the S1 battery life?\u003cbr\u003eThe battery of the S1 can last for 35 minutes of continuous use. This was measured with the S1 moving at a constant speed of 2.0m\/s on a flat surface. The battery life on standby is about 100 minutes.\u003cbr\u003e\u003cbr\u003eWhat is the maximum speed of the S1?\u003cbr\u003eThe maximum forward speed is 3.5m\/s, the maximum backward speed is 2.5m\/s, and the maximum speed when moving sideways is 2.8m\/s.\u003cbr\u003e\u003cbr\u003eWhat is the maximum transmission distance of the S1?\u003cbr\u003eConnection via Wi-Fi:\u003cbr\u003eFCC, 2.4GHz 140m, 5.8GHz 90m\u003cbr\u003eCE, 2.4GHz 140m, 5.8GHz 70m\u003cbr\u003eSRRC, 2.4GHz 130m, 5.8GHz 130m\u003cbr\u003eMIC, 2.4GHz 140m\u003cbr\u003eConnection via Router:\u003cbr\u003eFCC, 2.4GHz 180m, 5.8GHz 300m\u003cbr\u003eCE, 2.4GHz 180m, 5.1GHz 100m\u003cbr\u003eSRRC, 2.4GHz 180m, 5.8GHz 300m\u003cbr\u003eMIC, 2.4GHz 170m, 5.1GHz 180m\u003cbr\u003eNote: These results were achieved in an environment without signal interference or blockages. Blocked signals or signal interference will influence the transmission distance and effect. It is recommended to keep the S1 antenna as vertical as possible during use for optimal image transmission.\u003cbr\u003e\u003cbr\u003eWhat shooting methods does the S1 support?\u003cbr\u003eThe S1 supports two shooting methods: gel beads and infrared beams.\u003cbr\u003e\u003cbr\u003eIs the Blaster safe?\u003cbr\u003eThe Blaster can shoot gel beads and infrared beams. The S1’s blasting function meets the safety requirements of major countries and regions around the world. The S1 has an additional angle limit protection to make sure that it cannot launch gel beads when the pitch angle is higher than 10 degrees. The infrared beams are also safe and cannot cause any physical damage.\u003cbr\u003e\u003cbr\u003eIs RoboMaster S1 waterproof?\u003cbr\u003eNo\u003cbr\u003e\u003cbr\u003eFunctions\u003cbr\u003eWhat programming languages does the S1 support?\u003cbr\u003eScratch and Python.\u003cbr\u003e\u003cbr\u003eWhat programming platform does the S1 support?\u003cbr\u003eThe S1 only supports the official programming platform provided in the RoboMaster app known as RoboMaster Lab. This feature is available on mobile devices and computers. You can program, connect, and operate the S1 directly when using RoboMaster Lab.\u003cbr\u003e\u003cbr\u003eI don’t know how to program. Can I still use the S1?\u003cbr\u003eThere are abundant teaching resources in the RoboMaster app, including project-based tutorials, video courses, programming guides, and more, that allow users without programming experience to get started quickly. There are also numerous features that users can enjoy that do not require programming knowledge, such as FPV driving and Battle mode.\u003cbr\u003e\u003cbr\u003eHow can I implement\/use the programs that I write?\u003cbr\u003eYou can directly run your programs in RoboMaster Lab to see how they affect the S1. You can also set your program as a custom skill or Autonomous Program. Custom skills need to be selected using icons on the FPV interface as you control the robot in the app. Autonomous Programs are written into the robot itself and can be synced by pressing the Autonomous Program Button on the S1. You can also share your programs with others through the RoboMaster app.\u003cbr\u003e\u003cbr\u003eWhat kinds of stimulus can the S1 recognize?\u003cbr\u003e1. Clapping Recognition: the S1 can recognize two or three consecutive claps and be programmed to execute custom responses.\u003cbr\u003e2. Gesture Recognition: the S1 can detect human gestures such as hand or arm signals and be programmed to execute custom responses.\u003cbr\u003e3. S1 Robot Recognition: the S1 can detect other RoboMaster S1 units.\u003cbr\u003e4. Vision Marker Recognition: the S1 can identify 44 kinds of official Vision Markers, which are comprised primarily of numbers, letters, and special characters. All of the files for these Vision Markers can be downloaded at insert web address.\u003cbr\u003e5. Line Recognition: the S1 can detect and follow blue, red, and green tracks with a width of approximately 15-25 mm.\u003cbr\u003e\u003cbr\u003eWhat modules or components can be controlled with custom programming?\u003cbr\u003eMany parts of the S1 can be accessed and controlled through programming, including 7 motors, 6 hit detectors, 7 infrared sensors, 21 LED lights, 1 vision sensor, 1 microphone, 1 speaker, and 2 gyroscopes.\u003cbr\u003e\u003cbr\u003eWhat is the effective detection distance of the S1 in Follow mode?\u003cbr\u003eFollow mode is most effective when the subject is within a range of 1-3 meters from the S1.\u003cbr\u003e\u003cbr\u003eCan the RoboMaster S1 record photos and videos?\u003cbr\u003eWith a microSD card inserted, the S1 can capture photos and record 1080p videos; without a microSD card, it supports only 720p.\u003cbr\u003e\u003cbr\u003eWhere are the photos taken by the RoboMaster S1 stored? How can I export them?\u003cbr\u003ePhotos taken by the S1 will be stored on the microSD card (when one is inserted). You can download them to your local device or share them directly to social media. For photos on the microSD card, you can remove the card and use an external device to export.\u003cbr\u003e\u003cbr\u003eDo I need a microSD card to record and store video? Where are the videos taken by the RoboMaster S1 stored? How can I export them?\u003cbr\u003eUsers can record and store video using the RoboMaster app. However, if operating without a microSD card, 720p is the only resolution option. When using a microSD card, users can record in 1080p, although it should be noted that playback within the app will still be displayed in 720p. The 1080p version will be stored on the microSD card and can be exported using an external device.\u003cbr\u003e\u003cbr\u003eHow many S1 units can simultaneously participate during Battle mode?\u003cbr\u003eA maximum of six S1 units can operate at the same time during Battle mode.\u003cbr\u003e\u003cbr\u003eHow are Hit Points (HP) and other game rules determined and enforced?\u003cbr\u003eWhen you select Battle mode in the RoboMaster app, game rules and HP are detected and implemented with the S1 referee system, letting users enjoy a fair gaming experience.\u003cbr\u003e\u003cbr\u003eWhat routers are recommended for multiplayer gameplay?\u003cbr\u003eFor Battle mode, it is recommended to use a router that supports 5GHz to reduce signal interference. If you use a router that only supports 2.4GHz, you are recommended to choose the 3x3 MIMO Router. The following router brands and models are recommended: TP-Link TL-WDR8600; TP-Link TL-WDR5640 (for users in China) TP-Link Archer C7; NETGEAR X6S (for users outside of China).\u003cbr\u003e\u003cbr\u003eWhat ports does the S1 have and what accessories does it support?\u003cbr\u003eThe S1 has six PWM ports, which support servos, LEDs, drivers, and more. For more information on supported accessories, please visit programming guide.\u003cbr\u003e\u003cbr\u003eHow do I upgrade the firmware?\u003cbr\u003eDownload the latest firmware in the RoboMaster app and upgrade according to the instructions.\u003cbr\u003e\u003cbr\u003eProduct Components, Accessories\u003cbr\u003eHow do I charge the Intelligent Battery of the RoboMaster S1 and how long it will take?\u003cbr\u003eYou can charge the Intelligent Battery of the S1 with the official Intelligent Battery Charger. It takes about 90 minutes to fully charge.\u003cbr\u003e\u003cbr\u003eHow should I maintain the battery if it isn’t used for a long period of time?\u003cbr\u003eIt is recommended users charge and discharge their battery every three months to keep it active\u003cbr\u003e\u003cbr\u003eAre the gel beads made of safe material? What information do I need to know about using gel beads?\u003cbr\u003eThe gel beads for the RoboMaster S1 are made of safe, non-toxic gel that softens and expands when soaked in water. Please use them according to the instructions. At normal temperature, soak them in water for about four hours. The recommended proportion is 500 gel beads (about a full bottle top’s worth) per 1000ml of water. The gel beads will begin to evaporate and shrink shortly after they are removed from water, so it’s recommended to use them within 24 hours (in normal temperature and moisture conditions). You can also keep them into a sealed bottle to prolong the storage time. Both the product combo and PlayMore Kit come with gel beads. If you need more, they are available for purchase at the DJI Online Store.\u003cbr\u003e\u003cbr\u003eWhat is the capacity of the gel bead container?\u003cbr\u003eThe gel bead container can hold approximately 430 gel beads.\u003cbr\u003e\u003cbr\u003eHow can I assemble the S1? Are there any tutorials or instructions?\u003cbr\u003eDetailed assembly tutorial videos area available in the app and online. Users can also consult the official user manual for instructions. For more information, please check our tutorial videos.\u003cbr\u003e\u003cbr\u003eHow do I activate the RoboMaster S1?\u003cbr\u003eWhen you connect your RoboMaster S1 to the RoboMaster app for the first time, the activation prompt will pop up automatically. Follow the activation instructions in the app.\u003cbr\u003e\u003cbr\u003eWhat should I do if my RoboMaster S1 becomes disconnected with the app while the firmware is updating?\u003cbr\u003e1. When disconnected during the transmission of a firmware kit, repeat the update.\u003cbr\u003e2. When disconnected during the updating process, the update will not be influenced because the app does not participate in the updating process. LED and voice alerts on the RoboMaster S1 will keep users informed of the update status.\u003cbr\u003e\u003cbr\u003eWhat should I do if the firmware versions of any replaced accessories are not compatible with the existing S1 firmware?\u003cbr\u003e1. Users will be notified of any inconsistencies in firmware. \u003cbr\u003e2. Update firmware according to instructions.\u003cbr\u003e\u003cbr\u003eWhat can cause a firmware update failure?\u003cbr\u003e1. A firmware update will fail if you power off the device during the updating process.\u003cbr\u003e2. A firmware update will fail if the internet is disconnected while the firmware kit is being downloaded.\u003cbr\u003eDuring the updating process, it is normal for the app to disconnect from the RoboMaster S1, which will not affect the update. You can reconnect the app to the S1 after the update is completed. \u003cbr\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Thanksbuyer Online,SDR Radio, Testers and Measurement devices, Astronomy products, Audio Amplifer and Decoders","offers":[{"title":"Default Title","offer_id":41019877261361,"sku":"64962","price":621.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0578\/4790\/6353\/files\/1588217901-5.jpg?v=1780034308","url":"https:\/\/www.thanksbuyer.com\/de\/products\/for-dji-robomaster-s1-intelligent-educational-robot-with-hd-1080p-camera-remote-control-smart-robot-toy","provider":"Thanksbuyer Online,SDR Radio, Testers and Measurement devices, Astronomy products,  Audio Amplifer and Decoders","version":"1.0","type":"link"}