MWC MultiWii SE V2.5 Flight Controller W/ GPS NAV OLED Module Combo for 3D Fly

MWC MultiWii SE V2.5 Flight Controller W/ GPS NAV OLED Module Combo for 3D Fly

Features:
- Small size,35x35mm mounting holes
- 6 PWM input channels for standard receiver or PPM SUM receiver
- Up to 8-axis motor output
- Supported 2-axis gimbal and auto trigger controll
- FTDI/UART port for upload firmware, debug, Bluetooth module or LCD display
- I2C port for extend sensor, I2C LCD/OLED display or I2C-GPS NAV board for GPS  and Sonar
- Ultra low noise 3.3V LDO voltage regulator
- ATMega 328P Microcontroller
- MPU6050C 6 axis gyro/accel with Motion Processing Unit
- HMC5883L 3-axis digital magnetometer
- BMP085 digital pressure sensor
- PCA9306DP1 logic level converter

NEO -6 GPS V3.1 Module
Features:
- u-blox NEO-6M GPS module
- 5Hz update rate
- 32k I2C EEPROM for save configuration
- Build in 25 x 25 x 4mm ceramic patch antenna
- LNA and SAW chip
- 3.3V LDO low noise regulator
- UART (TTL) port with EMI protection
- 3V lithium Rechargeable battery
- Power and fix indicator LEDs
- Reverse polarity protection for input power

Default parameter
- Standard NMEA protocol
- Baud rate : 9600
- Nav rate : 1Hz
- TIMEPULSE (fix LED) rate : 1Hz

Spec:
- Dimension: 40 x 40 x 9mm
- Weight: 16.4g/18.6g (include cable)
- Hole diameter: 3.1mm

I2C-GPS NAV Module
 Features:
- All GPS data available via the I2C bus to connect to 328P Multiwii FC
- A LED on board show GPS 3D Fix status
- ATMega 328P Microcontroller
- 2 Molex 1.25mm 4Pin socket for GPS receiver and FC
- 2 port for ISP and FTDI

 Spec:
- Dimension: 20mmX30mm
- Height: 5mm
- Weight:2.4g/5g(include cable)
- Hole diameter: 3mm

Bluetooth parameter debug module
 Features:
- For Multiwii FC Configuration use with Android MultiWiiConfiguration
- UART TTL socket
 
MultiWiiConfiguration function
- Read and Write PID
- Setting switch for AUX1 and AUX2
- Monitor receiver signal and FC output signal
- Monitor All sensors and GPS signal
- Cablibration Magnetometer and Accelerometer
- Save and read profile

Spec:
- Dimension: 15mmX37.5mm
- Height: 5mm
- Weight:2.2g/3.9g(include cable)
- Hole diameter: 3mm

CRIUS CO-16 OLED Display Module

Features:
- High brightness, self-emission, high contrast ratio
- monochrome 128×64 dot
- 5V I2C interface
- Used for telemetry and debug MultiWii FC.
- Dimension: 27mmX27mm
- Height: 6.5mm
- Weight:3.7g/4.9g(include cable)

FTDI USB-TTL Module
- This is a basic breakout board for the  FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable  to work with official Arduino and cloned 5V Arduino boards. It can also be used  for general serial applications. The major difference with this board is that it  brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin  allows an Arduino target to auto-reset when a new Sketch is downloaded. This is  a really nice feature to have and allows a sketch to be downloaded without  having to hit the reset button. This board will auto reset any Arduino board  that has the reset pin brought out to a 6-pin connector.

Package Including:
- 1x MWC V2.5 SE Flight Controller
- 1x I2C-GPS NAV Module
- 1x CN -06 GPS receiver
- 1x CO-16 OLED Display Module
- 1x Bluetooth module
- 1x FTDI USB-TTL