{"product_id":"marauder-v8-4-in-1-development-board-5g-flipper-zero-external-module-kit-esp32c5x2-for-signal-data-analysis","title":"Marauder V8 4-IN-1 Development Board 5G Flipper Zero External Module Kit ESP32C5x2 for Signal\/Data Analysis","description":"\u003cp\u003e\u003cb\u003eExternal Modules Include:\u003c\/b\u003e\u003cbr\u003e1. 2.8-inch Marauder V8 (newly upgraded 5G version): The charging port of the Marauder is located at the top of the front; The indicator light is red when charging and green when fully charged. Marauder can share GPS data with Little Dolphin and automatically switch power.\u003cbr\u003e2. 433MHz RF module: A07 module is used, with a transmission power of 10dBm. When using, please insert Little Dolphin, enter the Sub GHz menu, click on \"Advanced Settings\" to view the module currently in use, and switch it to \"external\" mode.\u003cbr\u003e3. ESP32C5 (5G) module: default Marauder firmware burning; The programming interface is Type-C, located on the left side of the front of the device. Before programming, please hold down the button on the right side of the back of the device and insert a USB cable to activate programming mode.\u003cbr\u003e4. GPS module: The power supply of the GPS module can automatically switch between Little Dolphin power supply and body battery power supply, and the automatic switching scheme has been upgraded - it is powered by Little Dolphin when connected, and by the body's built-in power supply when disconnected.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eWhat do I need to do when I receive the device? How to do it?\u003c\/b\u003e\u003cbr\u003e1. To use the screen: toggle the right switch to turn it on.\u003cbr\u003e2. To use a 433M RF module: Insert Little Dolphin, enter the Sub-Ghz menu, click Advanced Settings to view the current module, and set it to \"external\".\u003cbr\u003e3. To use the ESP32C5 module: Insert Little Dolphin, find Monentum -\u0026gt; Protocol Settings -\u0026gt; GPIO Pin Settings -\u0026gt; ESP32 Pin Settings, and change the ESP32 pin to 13 or 14; Then go to APP -\u0026gt; GPIO -\u0026gt; ESP -\u0026gt; [ESP32] WiFi Marauder, enter this option to start using it.\u003cbr\u003e4. To use Little Dolphin's GPS function: Go to the Little Dolphin menu and select Monentum -\u0026gt; Protocol Settings -\u0026gt; GPIO Pin Settings, Change GPS Pin Settings to 15 or 16; Then enter APP-GPIO - [ESP32] WiFi Marauder-GPS Data and wait for a moment until the device detects the satellite and completes the positioning. Our GPS antenna is located in the upper left corner of the front.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eHighlights and Features:\u003c\/b\u003e\u003cbr\u003e- Newly upgraded with two ESP32C5 chips, the screen also supports 5Ghz signal\u003cbr\u003e- Newly upgraded battery display chip (MAX17048G)\u003cbr\u003e- Compared to the old V6, it has a better screen and better display effect\u003cbr\u003e- Battery capacity: 800mAh, charging 5V0.5A\u003cbr\u003e- Minor upgrade of the shell, with more precise details\u003cbr\u003e- Some pins are gold-plated, and each signal pin is equipped with TVS protection, improving the anti-static level.\u003cbr\u003e- Antenna configuration: WiFi antenna 3dBi\/11cm, GPS antenna 20dBi, 433M antenna 3dBi. All antennas use SMA male interfaces.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eHow to program firmware when firmware refresh crashes?\u003c\/b\u003e\u003cbr\u003e1. ESP32 Marauder v8 screen firmware: The top of the body is equipped with a Type-C interface; Please press and hold the BOOT button on the back, then turn on the power switch and connect it to the computer for burning (CH340 driver needs to be downloaded and installed in advance).\u003cbr\u003e2. ESP32C5 module: Turn on the power switch, turn off the power switch, press and hold button 1 (BOOT) while inserting the USB, connect to the computer and release the button to start programming. (Please note that the time from turning off the power switch to inserting into the computer should not exceed 10 seconds.)\u003cbr\u003e3. Download link for burning tool: http:\/\/docs.espressif.com\/projects\/esp-test-tools\/zh_CN\/latest\/esp32\/production_stage\/tools\/flash_download_tool.html\u003cbr\u003e\u003cbr\u003e\u003cb\u003eAbout Marks:\u003c\/b\u003e\u003cbr\u003e1: Boot button of ESP32C5 module\u003cbr\u003e2: ESP32 Marauder V8 Boot button\u003cbr\u003eA: Charging port\/programming port of this device\u003cbr\u003eB: ESP32C5 programming port\u003cbr\u003eC: ESP32 Marauder V8 SD card slot\u003cbr\u003eD: ESP32C5 SD card slot\u003cbr\u003eE: Marauder main switch\u003cbr\u003e\u003cbr\u003e\u003cb\u003ePackage Included:\u003c\/b\u003e\u003cbr\u003e- 1 x Flipper Zero External Module Kit\u003c\/p\u003e","brand":"Thanksbuyer","offers":[{"title":"Default Title","offer_id":41240771395633,"sku":"105398","price":56.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0578\/4790\/6353\/files\/20260927115732_a25eba38.jpg?v=1790494147","url":"https:\/\/www.thanksbuyer.com\/products\/marauder-v8-4-in-1-development-board-5g-flipper-zero-external-module-kit-esp32c5x2-for-signal-data-analysis","provider":"Thanksbuyer Online,SDR Radio, Testers and Measurement devices, Astronomy products,  Audio Amplifer and Decoders","version":"1.0","type":"link"}