{"product_id":"c-type-70-celsius-degree-300w-220v-ptc-heater-chamber-heater-temperature-controller-for-bambu-lab-p2s-p1s-x1c-3d-printer","title":"C-Type 70 Celsius Degree 300W 220V PTC Heater Chamber Heater Temperature Controller for Bambu Lab P2S\/P1S\/X1C 3D Printer","description":"\u003cp\u003e\u003cb\u003eModel Selection:\u003c\/b\u003e\u003cbr\u003e- C-Type: 10-70 Celsius degree, 300W, 220VAC, support heated bed linkage, simply connect the printer power supply.\u003cbr\u003e- E-Type: 10-70 Celsius degree, 200W, 110VAC, support heated bed linkage, suitable for 110V AC power.\u003cbr\u003e- F-Type: 10-60 Celsius degree, 200W, 24VDC, it does not support heated bed linkage. Do not connect the printer, use an independent power supply, and control multiple devices centrally. The farm version can be controlled manually or through a network.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eNote:\u003c\/b\u003e\u003cbr\u003e- The C-type uses 220V AC, and the vast majority of printers use this power supply, so it can be directly plugged into the printer power supply; When you do not want to wire from the printer, you need to connect 220V AC power externally. When using the external connection method, the heated bed linkage function will not work and can only be manually operated.\u003cbr\u003e- F-type does not come with a power supply and power cord, and customers need to provide their own power supply. The specification is a 24V DC power supply with a single device current of not less than 10A; The recommended power cord size is 1.5-2 square meters, with a plug specification of DC5.5*2.5.\u003cbr\u003e- Heated bed linkage requires printer support, not all printers are compatible.\u003cbr\u003e- The E-type is suitable for equipment in overseas 110V AC power supply regions such as the United States.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eImportant Reminder:\u003c\/b\u003e\u003cbr\u003e- This heater module is a semi-finished product and cannot work independently. It requires an additional 220V AC and 24V DC power supply. The wiring must be installed inside the 3D printer before it can be used. Incorrect operation may endanger personal safety. Customers need professional electrician knowledge to operate it.\u003cbr\u003e- Before performing any maintenance, installation, or disassembly work on the heater module, printer, and its electronic devices (including tool head cables), please turn off the printer power and disconnect the power connection to avoid circuit short circuits that may cause additional electronic device damage and personal safety hazards. Please confirm the temperature of the heated end and heated bed first, and avoid operating at high temperatures. If it is necessary to operate at high temperatures, please wear insulated gloves to ensure safe and effective maintenance work.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eUsing Instruction:\u003c\/b\u003e\u003cbr\u003e- It can be used for printing consumables that require maintaining the temperature of the chamber, such as ABS, which can be kept at a constant temperature of 10~70 degrees to increase printing effect and prevent edge curling;\u003cbr\u003e- Can be used to dry consumables in the chamber when not printing.\u003cbr\u003e- When the heating bed is started (or manually restarted each time), it will be heated to 45 degrees and held for a period of time before continuing to heat up to the set temperature. Reason: During the leveling and preparation process of the printer, there is a process of heating and cooling the print head. Premature heating to 70 degrees may cause the print head program to suspect that there is a problem with the cooling fan and prompt to check for the detachment of the print head casing, resulting in printing being aborted. Please confirm that your printer can withstand this high temperature before setting it to 70 degrees.\u003cbr\u003e- After printing is completed, do not immediately turn off the printer power and heater power switch (starting with the heated bed will be done after the heated bed signal stops, and manual start will be done after the manual switch is turned off). The heater will automatically delay for a period of time to cool down the heating element. Immediate power outage will cause the heating element to fail to cool down until the heater is damaged due to high temperature.\u003cbr\u003e- After the printing stops, the heater fan will continue to operate to maintain consistent cooling in all positions of the printing chamber until the temperature of the heating element and the chamber drops below 40 degrees Celsius and stops.\u003cbr\u003e- Blocking the waste port, fan outlet, and other air leaks in the printing chamber can significantly accelerate the heating rate and reduce constant temperature power consumption by increasing sealing.\u003cbr\u003e- The constant temperature is generally set at 60 degrees. If necessary, it can be set to a maximum of 70 degrees. It is best to manually adjust the temperature to 70 degrees after the printer has finished preparing the program for stable printing;\u003cbr\u003e- When using the heater, do not block the air inlet and outlet with objects.\u003cbr\u003e\u003cbr\u003e\u003cb\u003ePackage Included:\u003c\/b\u003e\u003cbr\u003e- 1 x Heater\u003cbr\u003e\u003cbr\u003e\u003cb\u003eSafety Reminder:\u003c\/b\u003e\u003cbr\u003e- The air outlet has electricity\/high temperature. When the 3D printer is powered on, do not touch the metal inside the air outlet to avoid the risk of electric shock! Before and after heating, the temperature here is high. Be careful not to get burned. Wait until the temperature drops and the printer power is disconnected before touching.\u003cbr\u003e- Before any operation on the printer body, the power supply of the printer must be disconnected. Live operation is dangerous and may endanger life safety.\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"width: 960px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/101528\/101528-01.jpg\"\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"width: 960px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/101528\/101528-02.jpg\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"width: 960px;\" src=\"https:\/\/www.comseek.com\/image\/catalog\/101528\/101528-03.jpg\"\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Thanksbuyer","offers":[{"title":"Default Title","offer_id":41028978901041,"sku":"101528","price":64.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0578\/4790\/6353\/files\/1776302929-2.jpg?v=1780372345","url":"https:\/\/www.thanksbuyer.com\/ru\/products\/c-type-70-celsius-degree-300w-220v-ptc-heater-chamber-heater-temperature-controller-for-bambu-lab-p2s-p1s-x1c-3d-printer","provider":"Thanksbuyer Online,SDR Radio, Testers and Measurement devices, Astronomy products,  Audio Amplifer and Decoders","version":"1.0","type":"link"}