JP-2565A Mach3 Stepper Motor Driver 256 Subdivision 1.5A-5A Large Current
  • JP-2565A Mach3 Stepper Motor Driver 256 Subdivision 1.5A-5A Large Current
  • JP-2565A Mach3 Stepper Motor Driver 256 Subdivision 1.5A-5A Large Current
  • JP-2565A Mach3 Stepper Motor Driver 256 Subdivision 1.5A-5A Large Current

  • SKU:18451
    (0 reviews)   Write a review(Get Thanksbuyer Points!)
  • Availability: In Stock     Reward Points: 4
  • Price:$43.24
  • Price in reward points: 432
  • Buy more, save more
  • Quantity 3+ units 10+ units 30+ units 50+ units More
    Price /Unit $42.38 $41.51 $40.21 $38.48 Contact US

JP-2565A Mach3 Stepper Motor Driver 256 Subdivision 1.5A-5A Large Current

Features:
- Large voltage.large current stepper motor driver
- 15-80V wide voltage input,out put current,1.5-5A(max)
- Over voltage/over current protection
- constant current drive
- Optical isolation signal input
- 2-4-8-16-32-64-128-256 steps
- 8 files drive current settings :(1.5A-2A-2.5-3A-3.5-4A-4.5-5A)
- Volatage:DC15-80V(sugguest 48V-60V)
- Half-flow control
- Positive power supply DC15-80V, the user can choose according to their needs.
-  In general the higher voltage will help improve motor high-speed torque, but will increase the drive loss and fever (recommended to use 60V voltage)
- GND with power to DC15-80V
- A + motor A phase, A+ and A- interchange ,be changed motor running direction A for 1 time
- A- is motor A-phase
- B+: motor phase B, B + B- intermodulation can change the motor running direction
- B-motor phase B
- PUL+  PUL-pulse signal input: +5 V. standard signal source, such as the control signal is 12V or 24V, need to add the current limiting resistor used ( 12V connected in series 1K-1.5K resistor) (24V cascading 2K-2.7K resistor) drive the internal resistance of 310 ohms
- DIR + DIR- :direction signal input: standard signal source +5 V. If the control signal is 12V or 24V, need to add limited resistor (12V connected in series 1K-1.5K resistor) (24V cascading 2K-2.7K resistor) drive internal resistance is 310 ohms the
- ENA + ENA- :enable signal input: The input signal is used to enable or disable the drive will cut off the motor phase current to the motor in a free state, then the step pulse response when not required for this feature, enable the signal-side floating +5 V. to (standard source, such as the control signal is 12V or 24V need to add the current limiting resistor (12V connected in series 1K-1.5K resistor) (24V cascading 2K-2.7K resistor) drive the internal resistance of 310 ohms)

Power supply voltage is selections:
-  The higher the supply voltage, high-speed motor torque the greater run-time, run the better, but the voltage is too high will lead to over-voltage protection, and may even damage the drive, and work under high pressure, low-speed running vibration in the low speed running, the motor speed at 200 rev / sharing, to make use of low voltage (less than or equal to 36V). such as high speed, may be appropriate to increase the voltage to use, but the maximum should not exceed the maximum voltage of 80V drive
Output current setting
-  Current setting the higher the value, the greater the motor output torque, but the current is large, the heat of the motor and drive increased, under normal circumstances is current set to the motor rated current or less than the rated 30%, in ensuring torque enough to minimize the set current, working long hours to ensure the stability of the drive and motor. high-speed work, an appropriate increase in current value to obtain the best operating results.
- Overall size: 120MM * 95MM * 47MM

Related Products
What other people are saying

Write a review

Your Name:
Your Review:
Note: HTML is not translated!
Rating:
Bad    
Enter the code in the box below:

Copyright © 2012-2015 ThanksBuyer.com . All rights reserved.