Běžná cena
$210.95
Běžná cena
Výprodejová cena
$210.95
Available Packages:
* Package 1: Motor (Built-In Driver)
* Package 2: Motor (Built-In Driver) + USB to CAN Module
* Package 3: Motor (Built-In Driver) + USB to CAN FD Module (Without Enclosure)
* Package 4: Motor (Built-In Driver) + USB to CAN FD Module (With Enclosure)
Advantages:
* Rated Torque: 8Nm
* Peak Torque: 20Nm
* Single-Turn Absolute Position of Output Shaft
* Built-In Driver
* Four Operating Modes
* Built-In Gearbox
* Built-In Dual Encoders
Motor Features:
* Dual Encoders: Provides single-turn absolute position feedback of the output shaft, preventing loss of the output shaft's absolute position after power failure.
* Integrated Motor and Driver Design: Compact structure with a high level of integration.
* PC-Based Visual Debugging: Supports visual debugging via PC software and firmware upgrades.
* CAN Bus Feedback: Provides real-time motor data, including speed, position, torque, and motor temperature.
* Dual Temperature Protection: Features dual temperature protection for enhanced operational safety.
* Trapezoidal Acceleration and Deceleration: Supports trapezoidal acceleration and deceleration in Position Mode.
Motor Specifications:
Motor Parameters:
* Rated Voltage: 24V (Supports 24-48V)
* Rated Current: 6.5A
* Peak Current: 18A
* Rated Torque: 8Nm
* Peak Torque: 20Nm
* Rated Speed: 120rpm
* Maximum No-Load Speed: 200rpm
Motor Characteristics:
* Gear Reduction Ratio: 6:1
* Number of Pole Pairs: 21
* Phase Inductance: 230μH (at 25°C)
* Phase Resistance: 0.36Ω (at 25°C)
Dimensions & Weight:
* Outer Diameter: 96mm
* Height: 40mm
* Motor Weight: Approx. 550g
Encoder:
* Encoder Resolution: 14-bit
* Number of Encoders: 2
* Encoder Type: Magnetic Encoder (Single-Turn)
Communication:
* Control Interface: CAN at 1Mbps
* Parameter Configuration Interface: UART at 921600bps
Control Modes:
* Control Modes: MIT Mode, Speed Mode, and Position Mode
Protection:
* Driver Over-temperature Protection: Protection temperature: 120°C. The motor will exit Enable Mode when the driver temperature exceeds the threshold.
* Motor Over-temperature Protection: Configurable according to application requirements. Recommended maximum temperature: 100°C. The motor will exit Enable Mode when the temperature exceeds the set threshold.
* Motor Overvoltage Protection: Configurable according to application requirements. Recommended maximum voltage: 52V. The motor will exit Enable Mode when the voltage exceeds the set threshold.
* Communication Loss Protection: If no CAN command is received within the configured timeout period, the motor will automatically exit Enable Mode.
* Motor Over-current Protection: Configurable according to application requirements. Recommended maximum current: 39A. The motor will exit Enable Mode when the current exceeds the set threshold.
* Motor Under-voltage Protection: The motor will exit Enable Mode if the supply voltage falls below the configured threshold. The supply voltage must not be lower than 15V.
Packing List:
Package 1: Motor (Built-In Driver)
* DM-J8006-2EC V1.1 Motor (Supports 24V-48V Power Supply) x 1
* GH1.25-3Pin Opposite-Side Cable (300mm) for Motor x 1
* GH1.25-2Pin Opposite-Side Cable (300mm) for Motor x 1
* XT30 Dual-Ended Cable (200mm) for Motor x 1
Packaging Details:
* Package weight: 0.7kg
Precautions:
1. Operate the motor strictly within the specified operating environment and maximum allowable winding temperature range. Failure to do so may cause permanent and irreversible damage to the product.
2. Prevent foreign objects or debris from entering the rotor, as this may cause abnormal rotor operation.
3. Before use, inspect all components to ensure they are in good condition. Stop using the motor if any components are missing, aged, or damaged.
4. Ensure all wiring is connected correctly and that the motor is properly and securely installed.
5. Do not touch the motor's rotating components during operation to avoid accidents. The motor may generate significant heat when delivering high torque. Take precautions to prevent burns.
6. Do not disassemble the motor without authorization. Unauthorized disassembly may affect motor control accuracy or even cause abnormal operation.






