Běžná cena
$378.20
Běžná cena
Výprodejová cena
$378.20
Friendly Reminder:
The LPT2000 Series and LPT3000 Series Low-Power Test Analyzers are specifically designed for battery-powered applications. They adopt a passive measurement approach and do not provide power to the external target board through their output terminals. Users must supply an external battery to power the target board when setting up the test environment.
Many low-power devices are powered by batteries, especially coin cell batteries, which are not ideal power sources and have inherent internal resistance. As the battery charge decreases, its internal resistance increases further. In other words, an ideal regulated power supply cannot accurately simulate the changes in internal resistance that occur under actual battery-powered conditions. This can lead to battery voltage decline and voltage sag under high-current loads, affecting the stability of the target circuit board under test.
For example, if the target board has an internal DC-DC converter, as the battery charge decreases, the battery's internal resistance increases and its voltage drops. To maintain a stable output voltage, the DC-DC converter draws more current than it would when the battery is fully charged, thereby accelerating battery depletion.
Failure Case: A low-power product powered by a coin cell battery was initially designed and tested using a regulated 3V power supply. The power consumption test results were satisfactory, and the estimated battery life was 3-5 years. However, after mass production, no issues were observed during the initial period of operation. Nearly one year later, a large number of products began experiencing abnormal and rapid battery depletion.
After analysis, it was found that the batteries had poor performance, with their internal resistance becoming excessively high over time. This resulted in excessive voltage sag and a significant increase in operating current. Consequently, the MCU repeatedly reset due to low voltage and could not enter sleep mode, leading to rapid battery depletion. These issues would not have occurred during testing if a regulated power supply had been used throughout.
Therefore, to obtain realistic power consumption results under actual battery-powered conditions while also evaluating battery characteristics, testing with an actual battery as the power source provides the most representative results.
Advantages:
* Micro Voltage and Current Analyzer, capable of measuring micro-volts
* Fully Isolated USB
* DC/AC Modes
* 100K Sampling Rate
* Over-current and Overvoltage Protection
* AC Mode: ±1nA to ±5A
* DC Mode: 1nA to 10A
* AC Mode: ±100uV to ±30V
* DC Mode: 100uV to 60V
Description:
The LPT3030-SCIENTIFIC Micro Voltage & Current Tester is specially designed for scientific research and applied research involving materials with electrical properties. It enables ultra-low-level measurements, detecting currents down to the nano-ampere (nA) range and voltages down to the microvolt (µV) range.
The product was developed by an engineer with nearly 20 years of experience in electronics design, manufacturing, and practical applications, with extensive expertise in weak-signal measurement. Drawing on years of experience and addressing real-world technical challenges, the team developed this reliable, original instrument featuring proprietary core technologies, guided by the philosophy of making technology more human-centered.
Features:
* Compact, lightweight design that fits easily in a briefcase for convenient portability.
* Low power consumption, powered and connected via a standard computer USB port.
* Isolated power supply design that isolates USB power to prevent unwanted ground loops and harmful power paths.
* Advanced dynamic self-calibration algorithm for optimal performance under varying environmental conditions.
* Hardware sampling rate of up to 100Kbps.
* Closed-loop noise current as low as 5nA, providing a clean measurement environment for low-power testing.
* Minimum current resolution of 1nA.
* Voltage sensitivity below 100µV.
* Voltage drop of less than 50mV at currents below 500mA.
* Dashboard-style software interface with clearly organized data for easy operation.
* Buzzer-based current alarm and over-current protection to help safeguard your test devices.
* Test data storage and retrieval, allowing you to review historical measurements anytime.
Applications:
* Current characteristic measurement of materials with micro-level currents
* Voltage characteristic measurement of materials with micro-level voltages
* Voltage data logging and analysis
* Current data logging and analysis
* Electrical characteristic measurement of bio-electrical materials
* Electrical characteristic measurement of piezoelectric materials
* Electrical characteristic measurement of optoelectronic materials
Packing List:
* 1 x LPT3030-SCIENTIFIC Analyzer
* 1 x 4mm Black Test Lead with Alligator Clip
* 1 x 4mm Red Test Lead with Alligator Clip
* 1 x 4mm Blue Test Lead with Alligator Clip
* 1 x USB Data Cable
* 1 x Carrying Case
Packaging Details:
* Package weight: 1.46kg
Note:
* Batteries and other items are not included in the package.


