Happymodel Mobula7 1S HD 75MM Whoop Drone FPV Drone with 1080P HD DVR (Receiver for Frsky)

Happymodel Mobula7 1S HD 75MM Whoop Drone FPV Drone with 1080P HD DVR (Receiver for Frsky)

Description:
Mobula7 1S HD version is a light and efficiency 75mm brushless whoop which provide 1080P HD video record function. A highly integrated AIO flight controller supports ESC with a maximum current output of 12A. We added black-box for this 1s 75mm HD recorder whoop. Now it could support gyroflow. Although the external black-box is not installed perfectly and insert SD card is not friendly to most of the people, however we still think it's really excited for this small whoop could record a video with gyroflow steady and keep safe flying.

Features:
* X12 5-IN-1 AIO flight controller
* VTX Power up to 400mw
* NEW RS0802 KV20000 motors
* 1080P HD Video record
* Blackbox Ready support GYROFLOW
* Smooth and powerful
* Compatible for 1S Lipo/LIHV

Specifications:
* Brand Name: Happymodel
* Item Name: Mobula7 1S HD 75mm Micro FPV whoop drone
* Wheelbase: 75mm
* Size: 99 x 99 x 45.5mm
* Weight: 33g

Package Included:
* Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame) x 1
* X12 flight controller for Frsky V1.0/V2.1 with built-in SPI 2.4G receiver for FRSKY x 1
* External Blackbox Module support gyroflow x 1
* RS0802 KV20000 brushless motor x 4
* Gemfan 1610-2 bi-blade propellers (4CW+4CCW) x 1
* Runcam Split3-Lite Camera+1080P DVR x 1
* 1S series balance charging board x 1
* Propeller disassemble tool x 1

Note:
* 1S 450mah/550mah/650mah batteries (not included) are recommended.

Spare Parts Specifications:
Motor
* Mode: RS0802 KV20000
* Configuration: 9N12P
* Stator Diameter: 8mm
* Stator Length: 2mm
* Shaft Diameter: 1.5mm
* Motor Dimensions (Dia.*Length): 10.5mm*13.5mm
* Weight(g): 2.0g
* No. of Cells (Lipo): 1S only

Propellers
* Weight: 0.24g
* Material: PC
* Pitch: 1 inch
* Props Dia.: 40mm
* Center Thickness: 5mm
* Center Hole Dia.: 1.5mm

Flight controller
* For X12 Frsky V1.0/V2.1 flight controller built-in SPI FRSKY 2.4G receiver Target: CRAZYBEEF4FR
* MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
* Sensor: ICM20689 or BMI270 (SPI connection)
* Mount hole size: 25.5 x 25.5mm
* Built-in 12A(each) Blheli_S 4in1 ESC
* Built-in Betaflight OSD (SPI Control)
* Built-in 5.8G 0mw~400mw VTX for OpenVTX
* Built-in receiver for ExpressLRS 2.4G or Frsky D8/D16 (optional)
* Built-in voltage detection
* Built-in current sensor

Onboard 4in1 ESC
* Power supply: 1S LiPo/LiPo HV
* Current: 12A continuous peak 15A (3 seconds)
* Programmable
* Factory firmware: Z_H_30_REV16_7.HEX
* Default protocol: DSHOT300
* Support firmware for Bluejay
* When use firmware for Blujay with 48khz, should set startup power to 1100/1200

Onboard SPI 2.4GHz Receiver for ExpressLRS (optional)
* Packet Rate option: 50Hz/150Hz/250Hz/500Hz
* Firmware version for ExpressLRS: V2.0
* RF Frequency: 2.4GHz
* Antenna: Enameled copper wire length 30mm
* Telemetry output Power: < 12dBm
* Receiver protocol: for SPI ExpressLRS
* Compatible with TX Module for ExpressLRS V2.0
* Couldn't flash separately firmware for ExpressLRS

Onboard receiver for Frsky SPI D8/D16 (optional)
* SPI BUS receiver for Frsky D8 D16
* Could working on protocol for FRSKY D8/D16/D16 LBT/REDPINE/SFHSS
* Channels: 8ch or 16CH
* No ground interference (Transmitter and receiver 1m/3.3ft from the ground): 200meter/656.2ft
* Fail-safe support

Onboard 5.8g for OPENVTX
* Firmware version: for OPENVTX
* For Smartaudio v2.1
* PIT Mode support
* RCE Mode support
* Channels:48ch
* Transmitting Power: 0/RCE/25mw/100mw/400mw
* Power supply: DC 5V
* Current (5v): < 650ma (400mw)

Runcam Split3-Lite
* Model: RunCam Split3-Lite
* Field of View(FOV): Recording FOV 165° (FPV FOV: 165° at 16:9, 130° at 4:3)
* Video Resolution: 1080 at 60fps/1080 at 50fps/1080 at 30fps/720 at 60fps
* Video File Format: MOV
* Image Resolution: 2MP
* TV Mode: NTSC (720*480)/PAL (720*576) Switchable
* Interface: JST 1.25mm / UART and SH 1.0mm
* Max Micro SD Card up to 64G (need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
* Hole Distance of Installation: 25.5 x 25.5mm
* PCB Size: 29 x 29mm
* Lens Module Size: 14 x 14mm
* Lens Specs: M9
* Power Input: DC 5-20V (Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera)
* Working Current: 450mA at 5V

External Blackbox and voltage booster module
* Size:18 x 15.5 x 4.5mm
* With Built-in Voltage booster module
* Weight: 1.5gram
* SD Card support max to 32GB
* SD Card need to use FAT32 Format
* Notes: Need to careful to insert the TF SD Card, and don't pull it out while install battery