JL1N-30MTY-W PLC Industrial Programmable Logic Controller Board Transistor Output 32-Bit CPU with D114 LED

JL1N-30MTY-W PLC Industrial Programmable Logic Controller Board Transistor Output 32-Bit CPU with D114 LED

Differences:
- MT: transistor output, MTY is an all-in-one model of a transistor with D114 digital tube.
- MR: relay output, MRY is an all-in-one model of a relay with D114 digital tube.

Description:
- Both input and output are protected by optocoupler isolation, and the transistor output version uses high-power transistors with high current, durability, and stability; The relay output version uses relays for Omron, which have a long lifespan and low failure rate.
- Adopting 32-bit ARM chips, it has the characteristics of stable system operation, fast response speed, long service life, and low failure rate; The system supports hardware encryption, and the encrypted program cannot be read, effectively protecting the fruits of labor.
- Two export routes support multiple communication protocols; Serial port 1 supports 232 communication, supports for FX protocol for downloading programs, connecting touch screens, configuring software, etc. Serial port 2 is 485 communication, supporting for MODBUS-RTU master/slave protocol, RS protocol, FX protocol.
- Diverse functions to meet different usage scenarios. Analog input/output support: 0-10V or 0-20mA, corresponding to digital quantity 0-4095; Support RTC real-time clock, temperature measurement, encoder, photoelectric switch, 485 communication, frequency converter, etc.

Supported Soft Components:
- Auxiliary relay:
  General use: M0-M383
  Power-off maintenance: M384-M1535
  Special use: M8000-M8255
- Status: S0-S999 for holding
- Timer:
  100MS: T0-T199 (0.1 - 3276.7 seconds)
  10MS: T200-245 (0.01 - 327.6 seconds)
  1MS cumulative type: T246 - T249 power-off maintenance
  100MS cumulative type: T250 - T255 power-off maintenance
- Counter:
  16Bit increment count: C0 - C15 (0 - 32767)
  16Bit increment count (power-off maintenance): C16 - C199
  32Bit bidirectional increase/decrease: C200 - C234
  High speed counter (power-off maintenance): C235 - C255
- Data Register:
  16Bit general: D0 - D127
  16Bit power-off maintenance: D128 - D3071
  16Bit indexing: V0-V7 Z0-Z7 16 points
  12Bit special use (AD): D8030, D8031, D8032, D8033 (input voltage range 0-10V)
  12Bit special use (DA): D8100, D8101 (output voltage range: 0-10V)
- Pointer:
  Used for JAMP and CALL branches: P0 - P127, 128 points
  Input interrupt timed interrupt: I0 ~ I5, 6 points
- Constant:
  Decimal number (K): -32.768~32.767 for 16bits; -2.147483648~2.147483647 for 32bits
  Hexadecimal number (H): 0~FFFF for 16bits; 0~FFFFFFF for 32bits

Supported Instructions:
- Basic instructions: LD, LDI, OUT, AND, ANI, OR, ORI, LDP, LDF, ANDP, ANDF, ORP, ORF, ORB, ANB, MPS, MRD, MPP, MC, MCR, INV, PLS, PLF, SET, RST, NOP, END
- Stepper instructions: STL (support up to 8-channel branches), RET
- Program flow: CJ, CALL, SRET, IRET, EI, DI, FEND
- Transmission and comparison: CMP, ZCP, MOV, BCD, BIN
- Four logical operations: ADD, SUB, MUL, DIV, INC, DEC, WAND, WOR, WXOR
- Cyclic shift: SFTR, WSFL
- Data processing: ZRST, DECO, ENCO
- High speed processing: REF, HSCS, HSCR, SPD, PLSY, PWM, PLSR
- Convenient instructions: ALT, RAMP
- Peripheral instructions: FROM, TO
- Peripheral unit: RS, incremental PID
- Positioning instructions: ZRN, PLSV, DRVI, DRVA
- Clock operation: TCMP, TZCP, TADD, TSUB, TRD, TWR, HOUR
- Compact comparison: LD=, LD>, LD<, LD<>, LD≤, LD≥, AND=, AND>, AND<, AND<>, AND≤, AND≥, OR=, OR>, OR<, OR<>, OR≤, OR≥

Features:
- Supports 32-bit instructions and supports adding P instructions.
- When the command is not supported, a 6506 fault will be detected.
- Tips: Some customers have reported that downloading programs is slow. By default, the length of the downloaded program is 8000 steps, but in reality, most customers write programs that do not exceed 2000 steps. Therefore, by setting it in the programming software for GX or WORK2, the download speed can be increased by 4 times.
- The setting method is as follows: After clicking the + sign before the parameter in the program data list, the PLC parameter will appear. Double click the PLC parameter to open the parameter setting interface. In the parameter setting interface, set the memory capacity from 8000 to 2000.
- PLC data download address: pan.baidu.com/s/1eRNhn3O
- The programming cable USB to TTL and USB to 232 drivers are the same. Driver address: http://pan.baidu.com/s/1jG5sLng
- After installing the driver, a serial port will appear. Please select a baud rate of 9600 when downloading.
- This PLC series has two independent 232 serial ports, one is a 9-pin port of 232 level (2: TXD 3: RXD 5: GND), and the other is a 4-pin port of TTL level (1: GXD 2: TXD 3: RXD 4: 5V). Both ports can be programmed and connected to a touch screen. When programming, use USB-232 cable for the 9-pin port; Use USB-TTL cable for the 4-pin port. When connecting the touch screen, the 232 level 9-pin port is directly connected to the touch screen using a 9-pin male to female cable (in reality, only 3 wires are used, namely 2-2, 3-3, and 5-5). The 4-pin port with TTL level needs to be converted to 232 level using our company's TTL to 232 conversion board (not included) in order to connect to the touch screen.
- Input high-speed pulses C235~C255 compatible with the F-X1N series.
- Y0 and Y1 can emit 10K pulses and are compatible with the F-X1N series.
- Encryption method: After the board is powered on, click online - remote operation - stop PLC [RUN changed to STOP] - click execute. After execution, the run light [RUN] on the circuit board will turn off. Login keyword - create new login keyword - enter 12345678 - confirm. After encryption, it can only be written from now on and can never be read again!

Package Included:
- 1 x Programmable Logic Controller Board

D114 LED Using Instruction:
- There are two modes in total, one is the main mode and the other is the input parameter mode.
1. As soon as the power is turned on, it enters the main mode. In this mode, the LED display shows the value of D114, and the button switch controls the closing and opening of the corresponding intermediate relay (M). The indicator light is controlled to turn on and off according to the closing and opening of the internal intermediate relay (M). Press and hold the SET key for 3 seconds to enter parameter input mode.
2. In input parameter mode, the values after data register D200 can be changed. The left two digits of the LED are used to display the number of the data register to be changed. You can press the upward triangle key (increase) or the downward triangle key (decrease) to change it. When changing, the read value will be displayed on the 4-digit LED on the right, and you can also use the UP and DOWN keys to change the value.
- Note: When the LED enters the input parameter mode, the d0 displayed on the left actually corresponds to the D register of the PLC as D200. The d1 displayed on the left actually corresponds to the D register of the PLC as D201, and so on. After changing the value, press and hold the SET key for 3 seconds to enter the main mode.