| Quantity | 3+ units | 10+ units | 30+ units | 50+ units | More |
|---|---|---|---|---|---|
| Price /Unit | $399.54 | $391.38 | $379.15 | $362.84 | Contact US |
GEPRC Naked Camera GP11 Lightweight FPV Drone Camera 4K MP4 Full Action Camera for CineLog35/Cinebot MAKE5
$658.72
GEPRC Naked Camera GP10 Lightweight FPV Drone Camera 4K MP4 Full Action Camera for CineLog35/Cinebot MAKE5
$571.27
GEPRC Naked Camera GP9 Lightweight FPV Drone Camera 4K MP4 Full Action Camera for CineLog35/Cinebot MAKE5
$435.24
LOTUSRC T580 Quadcopter AP/AV based ARTF - New Protocol
Main features of the T580 quadcopter:
1.ARTF
- Inertial-based(6DOF IMU) self-stabilization system.Good for AV/AP applications,but not suitable for acrobatics flights.
- 4 channels Tx is enough.No more switchs for the flight modes
- ARTF,no extra settings needed.Put on the props,the battery and the RX,then turn on the Tx to take off !
2.AP/AV based
- Auto Barometer-based altitude hold if no throttle input changed in 2s..
- X and Corss flight modes available.Only Cross mode was available in the beginning.But new improvements for the X mode had been tested successfully.
- Optional single axis camera mount(pitch) with double axis self-stabilization(pitch and roll).
- Larger MTM distance(580mm),larger payload (<580g),and longer flight time(25 mins with 3S Battery).Special props offered by the manufacture.
3.Powerful
-Optional GPS position hold(The GPS module still in internal testing, not included in this kit).
- Buzzer warning for low battery,and optional lights for night flight(The interfaces are available,but soldering should be done before coming out of the factory according to the demands of the costomers.In order to avoid some trouble of making the hardware easy to be damaged).
- Other features considering to be supported in the future:Configuration Software available and Firmware upgradable.
*This is the ARTF kit, basically speaking, you only need a receiver and transmitter to get it ready for flying.
Specifications:
|
Machine size |
608 × 608 × 243 |
mm |
±3mm |
|
Expand size of the largest |
885 × 885 × 243 |
mm |
|
|
Motor Wheelbase |
Diagonal line, the two motor centers wheelbase |
580mm |
±3mm |
|
Propeller |
1260, positive and negative special paddle |
12” |
|
|
Battery |
LiPo 3S 2200mAh 20C |
1P |
|
|
Single Weight |
No battery, receiver, load |
730g |
±10g |
|
Take-off weigh |
3S 2200mAh 1P Battery, receiver, head |
950g |
standard |
|
Payload |
Camera card |
≤230g |
standard |
|
Maximum power pulled |
Using the standard battery 1P |
2400g |
- |
|
Maximum payload |
Using the standard battery 1P |
≤580g |
- |
|
Maximum takeoff weight |
Using the standard battery 1P |
1800g |
Safety limit |
|
Flight distance |
Remote control device and battery capacity by the decision |
- |
- |
|
Flight Time |
3S 2200mAh 1P Battery, receiver |
12 minutes |
No wind hover |
|
Wind strength |
≤4 |
Class |
- |
Includes:
- 1x Pre-installed aircraft main body, including brushless ESC, flight control panel, motor.
- 1x pre-installed stands unit, including 4 fixed nuts.
- 3x pairs of special propellers in positive and negative.
- 4x bullet blade folders.
- 1x Velcro
* Pan & tilt for camera is not included.
Note: The battery capacity should be ≤2200mAh,or the ESC or flight controlller would be Burn.
Building video:
