GS-320 23MHz-6200MHz Vector Network Analyzer VNA Antenna Analyzer Wifi 5.8G Beidou 3.2" Touch Screen

GS-320 23MHz-6200MHz Vector Network Analyzer VNA Antenna Analyzer Wifi 5.8G Beidou 3.2" Touch Screen

Description:
GS-320 6G vector network analyzer VNA is especially suitable for the radio frequency circuit matching and debugging of Bluetooth, wifi, 2.4G, 5.8G, GPS, Beidou, various frequency band IoT devices, and various frequency band security products.

GS-320 23-6200MHz VNA (reflectometer) is designed to measure the matching characteristics of passive and active radio equipment, including antennas, cables, filters, attenuators, amplifiers, etc.

This device enables you to measure the parameters of complex reflection coefficient, standing wave ratio (VSWR), impedance, admittance, amplitude, phase, loss and distance to cable fault point.

Performance introduction:
GS-320 is made of durable aluminum shell and adopts the form of portable automatic instrument. Because of its light weight, compact structure and low energy consumption, it can measure the objects to be tested. This analyzer is especially suitable for companies engaged in the field of telecommunications, antenna installation and maintenance, and cellular communication amplification. With it, service centers and maintenance personnel can perform RF analysis on cables and antennas during commissioning or maintenance work. In addition, it is ideal for workshops, radio enthusiasts, educational institutions and laboratories.

The device has a 3.2-inch color resistive screen that can display measurement results and control the device.

You can use it to perform the following operations:
- Use Smith chart for impedance matching
- Measure standing wave ratio
- Measure the attenuation in cables
- Measure cable faults or irregular distances

Features:
- 3.2" color touch screen can quickly configure scan parameters and display measurement results
- Wide operating frequency range: 23MHz to 6200MHz
- Scanning speed up to 1000 points/sec
- High-precision measurement: 0.25 dB and 1.5° in the entire frequency range
- The ability to display up to four independent markers on all charts, so that the measured parameters can be accurately evaluated
- Display almost all possible descriptions of reflection coefficient
- Ability to measure cable fault and loss distance
- Support a host computer, which can be controlled through the PC interface (Please contact us for the host computer software)
- Light weight and small size. Weight 480g/1.1 lb; product size 145 x 72 x 24mm/5.7 x 2.8 x 0.9"
- Built-in battery can provide up to 4-hour duration time
- Able to power the device from a computer tablet or smartphone via a typc-USB cable: a battery that is not discharged in time will not stop the workflow

Specifications:
- Operating frequency range: 23-6200MHz
- Frequency resolution: 10kHz
- Maximum scanning points: 1000
- Scanning speed: 1000 points/sec
- The direction of the bridge, uncorrected in the entire range: > 12dB
- Effective directivity (after full single-port calibration) (Note 1): > 50dB
- SWR at the input: < 2
- Phase measurement accuracy (Note 1): > 1.50
- Amplitude measurement accuracy (Note 1): > 0.25dB
- Determine the resolution of the distance to the fault point (Note 2): (C x VF) / 2S m
- Maximum length of measuring cable (Note 3): 3000m/9842.5ft (VF=1)
- Maximum DC input voltage: 25V
- Display chart: Smith chart; polar chart; phase of reflection coefficient; amplitude; logarithmic amplitude; VSWR, fault distance; cable loss
- Working temperature range: 0 to +40℃
- Screen diagonal: 3.2 inches
- Screen type: resistive
- Screen resolution: 320х240
- Battery capacity: 4000mAh
- Battery duration time (Note 4): up to 4 hours
- Battery charging time: ~6 hours
- Dimensions: 145 x 72 x 24mm/5.7 x 2.8 x 0.9"
- Net weight: 0.48kg/1.1 lb

Note:
1. Warm up the device for at least five minutes, and perform measurement after complete (short-circuit, disconnection, load) single-port calibration. The ambient temperature change from calibration to measurement must not exceed ±3°C.
2. Where C is the speed of light (m/s); VF is the speed factor (the ratio of the propagation speed of electromagnetic waves in a cable to the propagation speed of electromagnetic waves in vacuum), according to the cable to take a value from 0.1 to 1; S is the scanning frequency range in the frequency task (Hz).
3. It depends on the attenuation of cables, which is the limit displayed.
4. After fully charged, add 20±5°C to the ambient temperature. The device has been calibrated in factories and the device connector is used as a reference. If you plan to use cable assemblies, adapters, etc. for measurement, you need to recalibrate. For this, please use the 50 ohm calibration kit SOL (S-short circuit, O-open circuit, L-load). SOL calibration kits are most commonly found in N type and SMA type. On the reference of planning calibration, select the right ones corresponding to the connector type.
5. It is not a professional measuring instrument and is suitable for amateur radio.

Package Included:
- 1 x GS-320 VNA
- 1 x USB Type-C Data Cable
- 1 x SMA SHORT
- 1 x SMA OPEN
- 1 x 50Ω LOAD
- 1 x Adapter N Female To SMA Male
- 1 x Stylus