RF49DR-Ultra 10M-6GHz 16R 16T RF Direct Acquisition Development Board UltraScale+ RFSoC 14Bit 7GSPS DAC +14Bit 2.5GSPS ADC

Main Chip Parameters:
- Master chip model: XCZU49DR-FFVF1760-2-I
- Clock recommended maximum speed: PLL/MMCM recommended maximum 775M
- PS application processor model: four core Cortex-A53, main frequency of 1333M
- PS real time processor model: dual core Cortex-R5, main frequency of 533MHz
- DDR specification model: DDR4, model of MT40A512M16LY-075:E; PS side, 4GB capacity, 64 bit-width, 2400M; PL side, 4GB capacity, 64 bit-width, 2666M
- Logic unit: 930300
- Lookup table: 425280
- DSP unit multiplier: 4272
- FlipFlops: 850560
- Block Ram: 38M Byte
- Ultra Ram: 22.5M Byte
- GTY (32.5G): 16
- Component temperature range: -40 to 85℃
- Speed level: -2
- Chip level: industrial

RF-49DR-Ultra Functional Interface Description:
- Development board power supply: power supply through dedicated DC-5.5 interface, 9-12V DC-IN interface
- Development board clock: 33.33M (PS), 100M (PL), 26M (PS GTR)/156.25M (GTY)
- Ethernet: gigabit RTL8211E, PS GEM3
- USB interface: USB3.0 SLAVE, also support USB3.0 HOST
- DEBUG: onboard UART+JTAG (FTDI solution) support ARM and FPGA development
- Optical port: one QSFP28 100GE optic port, maximum speed rate of 28Gbps
- EEPROM: one FM24C02 EEPROM, connect to PS
- SD card slot: SD1 of PS, 2.0 interface, can be started (SD support up to 32G)
- EMMC: SDO of PS, capacity of 32GByte
- LED and button: power on or off/reset, PS/PL button/PL LED, power status indicator/DONE indicator, USB indicator, etc.
- Boot setting switch: one BOOT toggle switch for boot setting
- Power-on/JTAG mode switch: one, used for setting automatic power-on/whether JTAG support external switch
- Onboard FLASH: 128M Bytes, two magnesium light particles
- Heat dissipation interface: two 12V heat dissipation interface, GH1.25-3P terminal
- Screen: onboard a 0.49-inch 64x32 OLED screen
- Synchronization and GPS: onboard MMCX leads out 5 IOs that can be used for synchronization/triggering, etc; Onboard a MAX-M10S GPS module for UBLOX
- Power supply monitoring: the development board has the function of monitoring power supply voltage and current
- Expansion IO port: lead out 16 x 3.3V single-ended TTL; 2lane PS GTR, 4lane GTY, the connector uses 60P BTB connector X0802WVS-60AS-LPV01
- FMC interface: one FMC HPC interface, including LA+GT part, without HA HB; GT part led out two Quad (8tx + 8rx)

RF Functional Interfaces Parameters:
- ADC number: 16-channel ADC, 14Bit, maximum sampling rate of 2.5Gbps
- DAC number: 16-channel DAC, 14Bit, maximum sampling rate of 7Gbps
- RF range: 10M to 6GHz
- SNR: >56dB at 1GHz (average battery than 57dB)
- Isolation degree: better than -70dB
- Channel consistency: the measured average error at 1G frequency is within the range of 0.25dbm, which is lower than 0.3dbm
- RF connector: MMCX female socket, requires MMCX male connector, other interfaces require adapter cables
- RF coupling mode: AC coupling mode, reserved ADC VCOM output
- Impedance control: RFSOC to Balun differential 100 ohms, Balun to MMCX single ended 50 ohms
- Note: The sampling rate of ADC and DAC is based on the actual device. ADC has a sampling rate of 2.5GSPS for 49DR 16-channel devices, and the sampling rate does not represent the RF frequency.

Package Included:
- 1 x Development Board
- 2 x Type-C Data Cable
- 1 x 12V/5A Power Adapter
- 6 x MMCX RF Cable