LED Full Color Controller H801RC 8-Port LED Controller Support Connection with TTL and DMX512 Signal

LED Full Color Controller H801RC 8-Port LED Controller Support Connection with TTL and DMX512 Signal

Description:
- H801RC can be directly connected to computer network interface, off-line controller and online master controller. It is an eight-port connectable and detachable off-line controller, which can control up to 8192 points.
- At present, the controllable driving chips include LPD6803, LPD8806, LPD6812, LPD6813, LPD1882, LPD1889, LPD1883, LPD1886, DMX512, HDMX, APA102, MY9221, MY9941; LD1510, LD1512, LD1530, LD1532, UCS6909, UCS6912, UCS1903, UCS1909, UCS1912, UCS512, UCS1603, UCS5603; WS2801, WS2803, WS2811, WS2 812, WS2821; SM16716, SM16711, SM16703, SM16709, SM16712, TLS3001, TM1812, TM1809, TM180 4, TM1803, TM1829, TM1814, TM1913, TM1914, TM1926, TM1906, TM512; INK1003, P9813, P9883, BS0825, BS0815, BS0901, LY6620, DM412, DM413, MB16023, MB16024, P943, P943S, P9411, P9412, QED3110.
- The supporting software of online controller is LED Broadcasting Software; the supporting software of offline controller is LED Programming Software.

Features:
- 8 output ports, controlling 8192 pixels at most. The maximum number of control points per port is 8192 divided by the actual number of ports used. The number of ports can be set to one, two, four or eight.
- It can be connected and disconnected, and can be directly connected to the computer network card, offline and online master control, and can also be directly connected to the switch and photoelectric converter.
- The synchronization performance is high, and the transmission delay of phase control is within 400 seconds, that is to say, cascade 100 sub-controls, and the delay is within 40 microseconds. The image is free of tear and mosaic.
- Single-line pneumatic chip can be set as TTL output or differential output.
- Addressable to H801DMX, H860, UCS512C, SM1651X.
- It has good control effect and accurate gray level control, and the gray level above 256 has been processed as hard Gamma.
- The transmission distance is far, and the transmission signal adopts standard Ethernet protocol, with a nominal distance of 100 meters. Sub-control, network relay and photoelectric conversion can be used as relay.
- The tracing clock speed can be adjusted to 100K-50MH.
- The grayscale technology and anti-Gamma correction technology are used to make the actual display more in line with the physiological feeling of the human eye.

Using Instruction:
- Use the network cable to connect the computer network card (or master control) to the sub-control NET1, NET2 to the next sub-control NET1, and so on, until the last one.
- Each sub-control can control up to 8192 pixel points, and each point of LPD6813 and P9813 occupies four bytes, so it can control up to 6144 points.
- In modeling settings, the number of lines can be one, two, four, and eight. The number of lines is the actual number of ports used.
  Terminal number 1  2  4  8
  Control points per port 4096  4096  2048  1024
  When the number of ports is 1, 2, or 4, the remaining ports can be used as backups of the ports. The number of points controlled during the actual use of each port is also related to the transmission capacity of specific lamps and moving chips.
- There are two indicators next to the network port seat. The upper one is green NET, which is always on after powering on. When there is a signal on the network cable, it will flash; The next one is red ACT, and the light control signal of this machine will make it flash, and the flashing frequency is related to the signal speed.
- When using the network card online, do not automatically obtain the IP address of the computer network card. Specify a fixed IP address. The subnet mask is 255.255.255.0, and other items do not need to be set.
- If there are multiple network cards, the first three bytes of the IP address cannot be the same, that is, it cannot be in the same network segment. The value range of the last byte is 1-254.

Package Included:
- 1 x Controller
- 1 x Power Cord