• N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version
  • N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version
  • N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version
  • N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version
  • N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version
  • N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version
  • N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version

N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 137.5MHz - 2.7GHz English Version

Tags: N1201SA

Availability: In stock, usually dispatched in 1 business day

  • Price:$90.79
  • Price in reward points: 908 Reward Points: 9
  • Quantity 3+ units 10+ units 30+ units 50+ units More
    Price /Unit $88.97 $87.16 $84.43 $80.80 Contact US
Quantity:

N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester 140MHz - 2.7GHz English Version

Instructions: Click here

Specifications:  
- Model: N1201SA
- Working currency:  137.5MHz~2700MHz    
- Stepped frequency  1kHz    
- Display  2.4inch TFT  
- Resolution ratio 320*240(QVGA)    
- Battery capacity: 2000mAH(7.4Wh)    
- Power consumption <1.5W    
- Charge current 400mA    
- Charge port USB    
- Auto power off can be set 5-60minutes    
- Measured parameters  resistence  reactance  standing wave s11    
- Resolution ratio 4 number    
- Frequency accuracy about 5ppm    
- Connector SMA-K    
- Impedance measurement range: 0.1~1000    
- Standing wave measurement range:1.000~65    
- S11(dB)measurement range: 0dB~-60dB    
- Working temperature:0~40 degree    
- Atmospheric pressure:860hPa~1060hPa    

Description:    
- This instrument has four interfaces: single point measurement, scanning, system information, correction and calibration    
- The default boot into single-point measurement interface.    

Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.    

Startup and shutdown    
- Hold down the CTRL key off press the power switch button.    
- The boot state, long press (2S above) the switch button, after the release, the instrument will shut down    
- The boot state, long press (2S above) the switch button, after the release, the instrument will shut down    

Advice when using:    
- In order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.    
- Try to use good quality RF cable and connectors.    
- Calibrated cable marked to the next may not need to calibrate and direct use.    
- Test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.    
- Measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.    
- If the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis.    

Package list:
- 1 x N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter
 

Write a review

Note: We will keep it confidential.
Note: HTML is not translated!
 
Captcha