mAt-10 Automatic Antenna Tuner 1.8-54MHz 0.1-30W For YAESU FT-817/818 QRP Radio

mAt-10 Automatic Antenna Tuner 1.8-54MHz 0.1-30W For YAESU FT-817/818 QRP Radio

Description:
The  mAT-10 is  a  compact  and  exquisite  tuner  designed  for  YAESU  FT-817/818,  it  can  also  be used  in other  QRP  transceivers.  When it is connected to FT-817/818 through a dedicated data cable mAT-CY, it is a dedicated tuner, which can achieve convenient "one-key tuning". If no data cable is used, it is a universal QRP tuner for all low-power transceivers.

The  mAT-10  is  connected  to  the  ACC  port  of  the  FT-817/818  transceiver  through  data  cable mAT-CY. The ACC interface allows an external device such as a PC or the mAT-10 to control the FT-817/818 by sending it serial commands.  The mAT-10 has the function of “one key tuning". When  the  multi-function  key  on  tuner  is  pressed,  the  mAT-10  command  FT-817/818  switches  to FM  mode,  reduce  output  power,  transmit  a  carrier,  initiate  a  tuning  cycle  and  then  restore  the transceiver to its previous mode and power level. This process is automated and does not require manual operation.

When  mAT-10  is  used  in  other  QRP  transceivers,  it  does  not  need  data  cables  and work  only  by connecting RF cables. The tuning process can be completed by pressing the Multi-function key on the panel. It is easy to operate.

The tuner can work within the range of 1.8MHz to 54MHz, at power levels up to 30 watts. It will tune dipoles, verticals, Yagis, or virtually any coax-fed antenna. It will match an amazing range of antennas and impedances, far greater than some other tuners you may have considered, including the built-in tuners on many transceivers.

The mAT-10 has 16,000 frequency memories.  When tuning on or near a previously tuned frequency, the mAT-10 uses “Memory Tune” to recall the previous tuning parameters in a fraction of a second. If  no  memorized  settings  are available,  the tuner  runs  a  full  tuning  cycle,  storing  the parameters  for  memory  recall  on  subsequent  tuning cycles  on  that  frequency.  In this manner, the mAT-10 “learns” as it is used, adapting to the bands and frequencies as it goes. You can also start a tuning cycle manually whenever necessary.

Two 10440 lithium batteries are installed in the interior of the mAT-10, which provides power for the tuner. Because  of  the  use  of  advanced  magnetic  retaining  relays,  the  power  consumption  of mAT-10 is  very  small, the  lithium  battery  can  work  for  a  long  time  after  it  is  fully  charged.  It is very suitable for outdoor use.  Special chargers are provided with tuners.  You must use its own charger to charge the tuner. It is dangerous to charge with an incorrect charger.

In addition to tuners, the package of mAT-10 includes data cable mAT-CY, special lithium battery charger and user manual.  They  are  provided  to  users  along  with  tuners,  and  do  not  need  to  be purchased separately.

Specifications:
- Max. 30W in SSB and CW modes, 5W in PSK and digital modes
- 1.8to 54.0 MHz coverage.16,000 memories for instantaneous frequency
- Tuning time: 0.1 to 5 seconds full tune, 0.1 seconds memory tune
- To tune the load capacity of 5 to 1500 ohm antenna
- For YAESU FT-817/818 radio via 8-core data cable
- Can also be used as a QRP tuner
- For dipoles, verticals, Vees, beams, long wire or any coax-fed antenna
- Dimensions: 13.8cm x 6.1cm x 2.3cm (L x W x H)
- Weight: 300g

Package Included:
- 1 x mAt-10 Automatic Antenna Tuner
- 1 x Charger  
- 1 x Data Cable
- 1 x Manual